. If acid enters eye, immediately flood eye with running cold water for at least 15 minutes and get prompt medical attention. The site navigation utilizes arrow, enter, escape, and space bar key commands. The controller should be mounted at least 4 from the floor and within 2 of the outlet. If you have a 2-prong receptacle, have a licensed electrician replace it with a 3-prong receptacle according to local codes and ordinances. .1014001 Battery box . When using the. Install a check valve on the top of the PVC pipe attached to the Pro Series pump. You will need to refer to it before attempting any installation or maintenance. An in-line check valve is recommended to prevent back-flow. As the pump evacuates the water from the pit the float will fall and turn off the pump. Mounting it above the drain tile would allow water to fill the drain tile before the pump is activated to pump out the water. . Make sure to reinstall the pin after the float switch is reconnected.Note: When mounting the float switch, position the bottom of the cage at the height you want the pump to activate. As the pump evacuates the water from the pit the floats will drop. . The POSITIVE (+) battery post usually has a larger diameter than the NEGATIVE, When connecting the battery cables, first connect the small ring on the end of the WHITE wire to the NEGATIVE, Two (2) acid packs to fill the dry batteries, A set of battery cables with rings on both ends to connect the two batteries together (available from Glentronics, Inc.). Limited WarrantyBy opening this package and using this GLENTRONICS, INC. product, you are agreeing to be bound by the terms of the GLENTRONICS, INC. limited warranty (warranty) as set out below. . If the adapter fits into the new pump, screw the pipe into the pump. Do not remove or alter their position as it will disrupt the timing of the controller and how long the pump runs. Place the pump with the PVC pipe attachment on the bottom of the sump floor next to the main AC pump. When AC power is restored, slide this switch back to the ON position. The float switch must not come into contact with the sump pit floor or wall. . Do not use an extension cord. . In most cases, the backup pump will fit next to the main AC pump in the sump pit. PHCC-2400 Pro Series 2400 Battery Backup Sump Pump System, PHCC-1850 Pro Series 1850 Battery Backup Sump Pump System, PHCC-1000 Pro Series 1000 Battery Backup Sump Pump System, PHCC-2200 Pro Series 2200 Battery Backup Sump Pump System, PHCC-1730 Pro Series 1730 Battery Backup Sump Pump System with Remote Terminal, PHCC-1730 Pro Series 1730 Battery Backup Sump Pump System, PHCC-1000 Pro Series 1000 Battery Backup Sump Pump System (without silence switch), PS-C33 Pro Series Pair of Pumps including S3033 and PHCC-2400, PS-C22 Pro Series Pair of Pumps including ST1033 and PHCC-1850, PS-C11 Pro Series Pair of Pumps including ST1033 and PHCC-1000, PS-C22 Pro Series Pair of Pumps including ST1033 and PHCC-1730, Safety Data Sheet for Maintenance Free / AGM Battery, B12-100 Pro Series Maintenance Free Battery, B12-90 Pro Series Maintenance Free Battery, PS-WiFi PHCC Pro Series CONNECT WiFi Module. . . Plug the control box into a properly grounded, 3-prong receptacle. Make sure the hole is above the water line, and below the check valve. .600 GPH @ 15' Pump dimensions w/elbow . . Avoid contact with skin, eyes, or clothing. DIRECT DISCHARGE TO THE OUTSIDE OF THE BUILDING (Diagram A). Once the float switch is in the desired position, securely tighten the hose clamp. Water SensorThe water sensor is designed to warn you of a potential flood. Make sure pump turns on at the intended level. ALWAYS disconnect the pump and float switch controller from the power source before servicing or making adjustments. Attach the wire to the pipe with a piece of tape. . Remove all debris from the bottom of the pit and make sure the pumps strainer is clear of debris. Enhanced ControllerThe Enhanced Controller features a dial to adjust the number of seconds that the pump will run after the float drops. a back-up pump or a second primary pump). GLENTRONICS, INC. will not cover the cost to reinstall the product, nor will GLENTRONICS, INC. pay the cost of having a plumber or contractor repair or replace the product. Have plenty of fresh water and soap nearby in case battery acid contacts skin, clothing or eyes. 5.Secure the pump wire so that the plug on the end will not fall into the sump. Then, plug the pump into the receptacle on the float switch cord. . ), Pump . Dual Float ControllerPlug the control box into a properly grounded, 3-prong receptacle, then insert the pump plug into the receptacle on the control box. Wash hands after handling. . Products received after the above mentioned timeframe fall outside of the timeframe for warranty service and will not be eligible for warranty service. .1011010 Float switch assembly w/hose clamp . The path of the rest of the pipe and the details of each installation will vary. More detailed instructions follow. In instances where the discharge line is exposed to freezing temperatures, the pipe must be sloped downward so any remaining water will drain out. Check valve on secondary pump will not close and. Failure to do so could result in property damage, serious injury, or death. Visit our website www.stopflooding.com for more information about the Pro Series AC sump pumps and battery backup sump pump products. . The maximum liability for any product described in this warranty shall be the cost of product replacement only. 3.Place the pump with the PVC pipe attachment on the bottom of the sump floor next to the main AC pump. If the float switch does not move freely the pump will not activate. ALWAYS unplug the main pump when installing or servicing the backup pump or float switch to avoid electric shock. DO NOT operate this product if it has been damaged in any way. If the battery is good, the light will go out. . .61>1166, Nfttgry iukpgr ofnjg cdr > nfttgrhgs . hlstruothdls oduj` rgsujt hl prdpgrty `fkfeg, tmhs kflufj, gvgl hc ydu `h` ldt hlstfjj tmg Qrd, _grhgs nfobup sukp pukp systgk, shlog tmhs, kflufj odltfhls sfcgty hlcdrkfthdl rgefr`hle, kfhl pdwgr suppjy hs hl f wgt nfsgkglt, ofjj, hlstfjjhle dr sgrvhohle tmg nfobup pukp dr, Pd rg`uog tmg rhsb dc gjgotrhofj smdob, ng, ogrtfhl tmft ht hs dljy odllgotg` td f prdpgrjy, dutjgt smduj` ng whtmhl tmg jgletm dc tmg, pukps pdwgr odr`, fl` ft jgfst 0 cggt fndvg. Charge in a well-ventilated area. DO. . As the pump evacuates the water from the pit the float will fall and the pump will run for an additional ten seconds to empty the pit. Reverse or replace the check valve. DO NOT use an extension cord. Be sure the area around the battery is wellventilated. Pmg Qrd _grhgs _ukp Qukp _ystgk hloju`gs9, nfttgry cjuh` jgvgj sglsdr, nfttgry ofnjgs, f 7, Pmg hltgrlfj odlstruothdl dc sdkg wgt ogjj nfttgrhgs, Ejgltrdlhos ofl ldt eufrfltgg tmg odkpfthnhjhty dc, fl` twd (>) omgob vfjvgs, `gpgl`hle dl tmg, F sgt dc nfttgry ofnjgs whtm rhles dl ndtm, gl`s td odllgot tmg twd nfttgrhgs tdegtmgr, Cjdft swhtom fssgknjy w/mdsg ojfkp . Primary pumps will not provide protection during a power outage. .4000 GPH @ 0 Pumping capacity . Install a check valve on the top of the pipe and tighten the bottom hose clamp. . Your email address will not be published. . Install a gate valve or ball valve if required by any codes. Note: DO NOT adjust the tether length to less than 4 as this can cause excessive stress on the cable or prevent the switch from operating. Power supply requirements . DO NOT use sump pumps in pits handling raw sewage, salt water, or hazardous liquids. . Fill the pit with water. The pumps strainer must be kept clear. Return the product to the manufacturer for any repairs at the following address: Glentronics, Inc., 645 Heathrow Drive, Lincolnshire, IL 60069. Please refer to the Troubleshooting Guide on page 5. . The pit cover either has a hole punch that will allow the cord to be passed through or one can be drilled in the cover. The manufacturer default is about 10 seconds. fvfhjfnjg crdk tmg kflucfoturgr, Ejgltrdlhos, Hlo. If the main power supply is in a wet basement, call an electrician. Call 800-991-0466, option #3 to order parts. Connect either wire to the common terminal. . . Cut the pipes and assemble them as shown in photo #7. Do not use this system to pump flammable or explosive fluids such as gasoline, fuel oil, kerosene, etc. CAUTION: To reduce the risk of hazards that can cause injury or property damage, observe the following precautions. The maximum amperage for the primary controller is 12 Amps. . MAKE SURE THERE IS A PROPERLY GROUNDED RECEPTACLE AVAILABLE. Select the installation method that will best suit your needs from the diagrams at the right. f rhsb dc chrg dr hliury crdk fl gjgotrhofj smdob. If the float switch does not move freely the pump will not activate. Connecting the Pump and Float Switch (Models VS and TS No Controller). . If you do not agree to the terms of the warranty, do not use the product and return it within the return period stated on your purchase receipt from the retail store or authorized distributor where you purchased it for a refund. Note: The 9V battery will only power the controller, not the pump. Make sure the hole is above the water line, and below the check valve. If the alarm continues to sound, replace the battery. on PRO SERIES PUMPS Sump Pumps Instruction Manual, Understanding the Warnings & Alarms Deluxe Controllers, Accessories for the Deluxe Controller Connect Modules and High Water Alarm Connect Modules WiFi Module Home Automation Module, Bissell 1986 Series Revolution Pet Pro User Guide, Midiplus X pro mini Series MIDI Keyboard User Manual [X4 pro mini, X6 pro mini], Eemax Pro Series XTP Tankless Electric Water Heaters User Manual, KitchenAid Pro Line Series Blender User Guide, ORION 5222 IntelliScope-to-PC Interface Cable Instruction Manual, CALIBER BC 112SA Active 12-Inch Subwoofer User Guide, IKEA 003.923.24 RYTMISK Wall Mounted Extractor Hood Stainless Steel 60cm Instruction Manual, LUPINE C14 Electric Bike Rear Light Instruction Manual, AXIS Q6315-LE PTZ Network Camera Installation Guide, ZERFUN G8 Pro Wireless Microphone System User Manual, Airrex Infrared Heater AH-200/300/800 User Manual, 2017 Toyota Camry Hybrid LE Fuse Box Diagrams, 2017 Mitsubishi Lancer 4WD Fuse Box Diagrams, Mitsubishi Lancer Passenger and Engine Fuse Box Diagram, Mira Honesty ERD Bar Valve and Fittings User Manual, The float switch is not connected to the controller, Check connection of the float switch to the controller, Water is not high enough to activate the pump, Make sure float switch is positioned properly, Replace float switch with new float switch, Overburdened due to heavy sand content in the water, Use water filter or replace with a higher wattage pump, Pump running continuously with no water present, Float switch or sensor is mounted too low, Raise float switch or adjust timer (Enhanced or Deluxe Controller), One or both of the floats is obstructed and cannot drop down. Water will lift the bottom float by a 14, which will activate the pump. .non-corrosive, will not rust Pump . To reduce the risk of electric shock, be certain that it is only connected to a properly grounded, 3-prong receptacle. Failure to read and follow these warnings and instructions could result in property damage, serious injury, or death. While the pump is running, make sure pump is evacuating water at a good pace. Do not use your product until you have read the terms of the warranty. When service is required, contact Glentronics technical support at 800-991-0466, option #3, or send an e-mail to service@glentronics.com. The Pro Series Connect Modules are separately sold accessories that will allow the user to stay connected and receive remote notifications of potential problems and needed maintenance while away from home. _mduj` fly kfjculothdl dr gkgregloy, dr tmg FO pdwgr, tmg Qrd _grhgs systgk whjj sdul`, odltrdj ulht whjj hl`hoftg tmg ofusg dc tmg, Cdr f``g` rgjhfnhjhty, tmg cjdft swhtom mfs, ldt, dlg, nut twd cjdfts kdultg` whtmhl f prdtgothvg, prdtgothvg ofeg prgvglts `gnrhs dr dtmgr whrgs. . ALWAYS remove the power cord from the electrical outlet before connecting or disconnecting the battery cables. If a 1/8 hole is not drilled in the pipe above the pump, an air lock may prevent the pump from operating. WARNING: Make sure the outlet is single phase, 115V and 60HZ for all the pump installations. During times of very heavy rain, many storm sewers fill up. .1020011 Fluid sensor assembly . Check the polarity of the battery posts. When used with the Enhanced Controller, the dual float switch has a safety locking pin. This manual should be retained for future reference. Tab will move on to the next part of the site rather than go through menu items. The float switch must not come into contact with the sump pit floor or wall. . This pump is wired with a 3-prong grounded plug. the pump to any existing pipes; it should be placed on the floor of the sump. . The timer can be adjusted from 5-45 seconds. . The use of a Pro Series, cables specifically designed for this use are, system to support your main AC sump pump, and. This manual contains important SAFETY WARNINGS and OPERATING INSTRUCTIONS. . Should any malfunction or emergency. . Wear eye and clothing protection and avoid touching your eyes while working with battery acid or working near the battery. Hold the float switch to the discharge pipe so the cage is below the bracket. Either the float is stuck in the up position, there is a mechanical problem with the pump, or there is a problem with the plumbing connections. A pit cover is recommended for all installations as a safety measure and to help prevent debris from falling into the pit. If for anyreason the lower float does not activate the pump, the water will rise and activate the second switch. To avoid debris from pouring onto the float, it should be positioned on the side of the discharge pipe opposite the drain tile. . Now connect the bottom of the assembly to the check valve and tighten the hose clamp. Be sure check valve is installed with flow arrow pointing up and out of the pit. Water will raise the float to activate the pump. To reduce this risk, observe the following precautions. Any and all causes of action arising from, filed as a result of or in reference to, this warranty or the products described under this warranty shall be governed by and construed under the laws of the State of Illinois.
Sitemap 24